Friday, June 05, 2009
Cage continues



Front legs bent up - made sure that they fitted above the top of the door frame - so you dont twat your head every time you get in and out - not going to have a head lining either so a bit more room to play with

Although cage is well up in the roof - its quit easy to get the mig torch around 360 deg's
Now the interesting bit - triangulating it back across at floor level to the inner plate the will take a longitudinal tube from the top of the rear hoop - going to run a middle and top cross brace between the front legs of the main cage over the gearbox and at the roof lip - who needs sun visors?
Front main bar in at roof level - made sure its well up out of eye sight
Going to modiy the inner door skin as I need clearance for seats
Drivers door bar in - not posible to replicate the passenger side arrangement due to the pedals - bent up some 4mm plate and going to weld it to the front leg off the cage - and on top of the front body mount/outrigger


Ran a cross brace at the base of the rear hoop - just incase

Posted by
GT5-R
Monday, May 25, 2009
Cage Fabrication
Really got some amps into the 48mm O/D seamless tube and plate - takes ages to 'birds mouth' all the connecting links

Sarted the cage install - rear hoop now welded in - fixed some 6mm angle/plate down the heel board so really solid mounting - going to run the front cage and triangulate down to the front chassis outriggers
Longitudinally brace down to the gearbox area and back down to the rear deck
Really got some amps into the 48mm O/D seamless tube and plate - takes ages to 'birds mouth' all the connecting links

Solid as a rock - will plate across to the tub aswell to give it even more rigidity - much better than that bolt in off the shelf crap you buy with an FIA approved sticker - know what I'd rather be in if it rolls over!!!!
Posted by
GT5-R
Tuesday, May 12, 2009
Project floor pan - strengthening and areo dynamics
Tooks some intial dimensions and will overlay images in AutoCAD to make a 1:1 template - then dxf it out to take down to the water jet cutter

Flattened out the pan and welded it back in

Looking now at fabricating a complete ally under pan - which will cover floor and chassis from front cross member to rear valance
Tooks some intial dimensions and will overlay images in AutoCAD to make a 1:1 template - then dxf it out to take down to the water jet cutterOnly problem is when the drives side floor pan was lowered by 1'25'' to well in the pan (where the bung hole is) sat below the level of the ally plate - so chopped it out the way was the easiest solution

Flattened out the pan and welded it back in

Posted by
GT5-R
Almost 36 years untouched
Stripped the roof back - lots of surface rust - especially around the rear hatch hing mountings - loads of rust killer
Good thing with the shell being on its side you can pour rust killer down all the joints and holes in the roof pressings and down the inside of the front roof panel
Note the underside of the roof lip mod!!!!
Stripped the roof back - lots of surface rust - especially around the rear hatch hing mountings - loads of rust killer
Good thing with the shell being on its side you can pour rust killer down all the joints and holes in the roof pressings and down the inside of the front roof panelNote the underside of the roof lip mod!!!!
Posted by
GT5-R
Wednesday, May 06, 2009
First time in 15 years its turned a wheel – well sort of !!
Big push now on the get the tub sprayed – so time to split chassis and tub apart and put some rubber on the corners
Quite pleased with how the rear suspension geometry sits with some weight on it – solid as a rock – have got quite a bit of adjustment up and down on the upright and shock so when fully laden with tub will see what’s needed
Inside floor pan was a bit of a disaster zone - gone a bit rusty - so again gone over with the wire brush attachement
Big push now on the get the tub sprayed – so time to split chassis and tub apart and put some rubber on the corners
Quite pleased with how the rear suspension geometry sits with some weight on it – solid as a rock – have got quite a bit of adjustment up and down on the upright and shock so when fully laden with tub will see what’s neededShell going on it side to get at all the areas I could not reach from above
Quite a bit of overspray and angle grinder crudd all over the place, a few nicks and scratches – will take little work to clean up
Inside floor pan was a bit of a disaster zone - gone a bit rusty - so again gone over with the wire brush attachement
Posted by
GT5-R
Friday, May 01, 2009
Friday, April 24, 2009
Steering Column mods
In for a penny and all that - the thought of replacing the standard GT6 steering column bushes (again) !!!!
Anyway going to use a complete Volvo steering column/ignition barrel so only problem is attaching it the the GT6 rack
So easy mod really - cut down the existing shaft
Chop a bit of the out sleave from where the clap is - which happens to have the same o/d as the Volvo steering knuckle - less a machine flat

Tig the 2 together having machine a groove in the shaft to make sure the weld really penetrates into the shaft


Tickle it round with the tig

Jobs a gooden - just need my mate to sort out machining a flat so as it inserts into the Volvo steering knuckle - job done
In for a penny and all that - the thought of replacing the standard GT6 steering column bushes (again) !!!!
Anyway going to use a complete Volvo steering column/ignition barrel so only problem is attaching it the the GT6 rack
So easy mod really - cut down the existing shaft
Chop a bit of the out sleave from where the clap is - which happens to have the same o/d as the Volvo steering knuckle - less a machine flat
Tig the 2 together having machine a groove in the shaft to make sure the weld really penetrates into the shaft


Tickle it round with the tig

Jobs a gooden - just need my mate to sort out machining a flat so as it inserts into the Volvo steering knuckle - job done
Posted by
GT5-R
Wednesday, April 15, 2009
Lost the plot over the last 3 months and not really done anything with the car
Finally finished the 3' down pipe and the first section under the gearbox - less a bit of flap disc action too clean it up and get it blasted and coated
Started back on the rear end panelling and rear deck area - I really hate body work and have lost the will to live with it !!!
Starting to look at jigging up the roll cage - going to weld it in and mount to chassis
Not going to run a boot floor for easy access to tank etc - but will be looking at some under body areo mods so might even get a complete alloy flat plate to cover the entire underneath of the tub
Going for the single NASCAR type look wiper blade
Renault wiper motor tucks up nicely and gets rid of that piece of crap taking up space on the bulk head
Posted by
GT5-R
Monday, December 29, 2008
Subscribe to:
Posts (Atom)

































