Monday, May 25, 2009

Cage Fabrication

Sarted the cage install - rear hoop now welded in - fixed some 6mm angle/plate down the heel board so really solid mounting - going to run the front cage and triangulate down to the front chassis outriggers





Longitudinally brace down to the gearbox area and back down to the rear deck






Really got some amps into the 48mm O/D seamless tube and plate - takes ages to 'birds mouth' all the connecting links

















Solid as a rock - will plate across to the tub aswell to give it even more rigidity - much better than that bolt in off the shelf crap you buy with an FIA approved sticker - know what I'd rather be in if it rolls over!!!!



Tuesday, May 12, 2009

Project floor pan - strengthening and areo dynamics

Looking now at fabricating a complete ally under pan - which will cover floor and chassis from front cross member to rear valance

Tooks some intial dimensions and will overlay images in AutoCAD to make a 1:1 template - then dxf it out to take down to the water jet cutter


Only problem is when the drives side floor pan was lowered by 1'25'' to well in the pan (where the bung hole is) sat below the level of the ally plate - so chopped it out the way was the easiest solution


Flattened out the pan and welded it back in







Almost 36 years untouched

Stripped the roof back - lots of surface rust - especially around the rear hatch hing mountings - loads of rust killer

Good thing with the shell being on its side you can pour rust killer down all the joints and holes in the roof pressings and down the inside of the front roof panel


Note the underside of the roof lip mod!!!!

Wednesday, May 06, 2009

First time in 15 years its turned a wheel – well sort of !!

Big push now on the get the tub sprayed – so time to split chassis and tub apart and put some rubber on the corners



Quite pleased with how the rear suspension geometry sits with some weight on it – solid as a rock – have got quite a bit of adjustment up and down on the upright and shock so when fully laden with tub will see what’s needed


Shell going on it side to get at all the areas I could not reach from above


Quite a bit of overspray and angle grinder crudd all over the place, a few nicks and scratches – will take little work to clean up






Got the last bit of rust out the tub as well – shell is far too good to trackday really – but do I look bothered – more solid it is less it will bend!!!!!!
Nice shot of engine and gearbox - needs a good clean up





Given the underside a really good clean up and good dose of rust kill




Inside floor pan was a bit of a disaster zone - gone a bit rusty - so again gone over with the wire brush attachement

Friday, May 01, 2009

Rear Deck Area

Started panelling in the rear deck - want to make it fire proof if nothing else

Bit of 20mm box and a flat sheet

Left a hole for removing the alloy tank

Spotted togehter and will fibreglass over all the gaps in the inner rear wing


Friday, April 24, 2009

Steering Column mods

In for a penny and all that - the thought of replacing the standard GT6 steering column bushes (again) !!!!
Anyway going to use a complete Volvo steering column/ignition barrel so only problem is attaching it the the GT6 rack

So easy mod really - cut down the existing shaft

Chop a bit of the out sleave from where the clap is - which happens to have the same o/d as the Volvo steering knuckle - less a machine flat








Tig the 2 together having machine a groove in the shaft to make sure the weld really penetrates into the shaft











Tickle it round with the tig


Jobs a gooden - just need my mate to sort out machining a flat so as it inserts into the Volvo steering knuckle - job done


Wednesday, April 15, 2009

Lost the plot over the last 3 months and not really done anything with the car


Finally finished the 3' down pipe and the first section under the gearbox - less a bit of flap disc action too clean it up and get it blasted and coated




Started back on the rear end panelling and rear deck area - I really hate body work and have lost the will to live with it !!!


As you can see lots of fabrication required - will give a good solid base for the full cage







Starting to look at jigging up the roll cage - going to weld it in and mount to chassis



Not going to run a boot floor for easy access to tank etc - but will be looking at some under body areo mods so might even get a complete alloy flat plate to cover the entire underneath of the tub


Going for the single NASCAR type look wiper blade

Renault wiper motor tucks up nicely and gets rid of that piece of crap taking up space on the bulk head




Monday, December 29, 2008

Finally got 4 hours back on the project today – welcome relief from Crimbo and all that - bought in some pre formed bends so I can fabricated my own systen

Sarted fabrication of the down pipe today – 3’ tube all the way through – monster





Just need to weld the lambda sensor insert in and mig it up – job done

Thursday, November 20, 2008

Body work and Aerodynamics of sorts

Finally got around to fitting the rear valance and slapping a coat of primer over most of the shell

Wheel arch mods look much better now with a coat of primer







Also been looking at improving the areodynamics at the back - not really sure about this - might try and move it further back




Tuesday, October 14, 2008

Only GT6 with a drivers airbag?

Using the Volvo steering column has serveral advantages - one being its completely adjustable - up and down & forwards and back ward - unlike the micky mouse Triumph arrangement. Also means I can plug the Volvo wiring loom straight in - so no messing around with 2 looms - indicators, lights, ignition barrell etc


Will obviously disable the air bag for track use - but all that said a modern safety upgrade???

Sunday, September 21, 2008

Aero dynamics - well sort of !!

Been wanting to look under the roof lip strip since 1987 when I did some minor repairs - which have pretty much lasted the time and saved the roof lip



On the face if it the lip was pretty good - however two minor cuts with a hacksaw and the finishing strip was off to reveal rust!!!










Most of the lip although pretty rusty is all in one piece - until it got chopped off with the grinder




Not sure about you but I've never seen a GT6 that has been de-seamed that looks right - it looks like when you cut your eye brows off - not that I've done that either

Rather than de-seaming I'm removing the lip over the majority of the screen and seam welding the roof & leaving 3 short sections so I can put the finishing strip back on - this will allow the air to flow between the it rather than around it




You can just see the gap below - hope to reduce drag around the windscreen area




Roof back to bare metal

Sunday, September 14, 2008

Body Work Continue's

I really hate body work!!!

Been working away on the brake conversion and the rear end mods

Bulkhead has been cut out the way completely along with the dash top and dash itself - going to graft a Volvo steering column in as its going to a much easier to sort all the electrics out - indicators lights and ignition






Cut the old braces out and reused so should stiffen it all up


Servo unit fits like a glove - however will need to run a remote reservoir as I would need to chop the windscreen frame out!!







Back end is on going and stating to get on my t*ts

Had to revamp the location for the wipe motor due to the servo mods - going to run a single blade NASCAR style - so plugged the original holes and washers