Monday, December 29, 2008

Finally got 4 hours back on the project today – welcome relief from Crimbo and all that - bought in some pre formed bends so I can fabricated my own systen

Sarted fabrication of the down pipe today – 3’ tube all the way through – monster





Just need to weld the lambda sensor insert in and mig it up – job done

Thursday, November 20, 2008

Body work and Aerodynamics of sorts

Finally got around to fitting the rear valance and slapping a coat of primer over most of the shell

Wheel arch mods look much better now with a coat of primer







Also been looking at improving the areodynamics at the back - not really sure about this - might try and move it further back




Tuesday, October 14, 2008

Only GT6 with a drivers airbag?

Using the Volvo steering column has serveral advantages - one being its completely adjustable - up and down & forwards and back ward - unlike the micky mouse Triumph arrangement. Also means I can plug the Volvo wiring loom straight in - so no messing around with 2 looms - indicators, lights, ignition barrell etc


Will obviously disable the air bag for track use - but all that said a modern safety upgrade???

Sunday, September 21, 2008

Aero dynamics - well sort of !!

Been wanting to look under the roof lip strip since 1987 when I did some minor repairs - which have pretty much lasted the time and saved the roof lip



On the face if it the lip was pretty good - however two minor cuts with a hacksaw and the finishing strip was off to reveal rust!!!










Most of the lip although pretty rusty is all in one piece - until it got chopped off with the grinder




Not sure about you but I've never seen a GT6 that has been de-seamed that looks right - it looks like when you cut your eye brows off - not that I've done that either

Rather than de-seaming I'm removing the lip over the majority of the screen and seam welding the roof & leaving 3 short sections so I can put the finishing strip back on - this will allow the air to flow between the it rather than around it




You can just see the gap below - hope to reduce drag around the windscreen area




Roof back to bare metal

Sunday, September 14, 2008

Body Work Continue's

I really hate body work!!!

Been working away on the brake conversion and the rear end mods

Bulkhead has been cut out the way completely along with the dash top and dash itself - going to graft a Volvo steering column in as its going to a much easier to sort all the electrics out - indicators lights and ignition






Cut the old braces out and reused so should stiffen it all up


Servo unit fits like a glove - however will need to run a remote reservoir as I would need to chop the windscreen frame out!!







Back end is on going and stating to get on my t*ts

Had to revamp the location for the wipe motor due to the servo mods - going to run a single blade NASCAR style - so plugged the original holes and washers








Monday, September 01, 2008

Breaking System Mods

Started work on the braking system - using a Subaru Impreza Turbo servo unit


Easier to cut the entrie rear bulk head panel out the way

Reshaped the top of the scuttle


Need to make a bracket then reinforce the bulkhead



Started to sus out the wiring loom - nightmare!!!!










Finished off the oil cooler as well




Thursday, June 26, 2008

Rear Wheel Arch Mods

Started the rear end mods to accommodate the wider wheel track and 16’ rims










Decided to roll a new inner wheel arch from a sheet of 18 guage to replace the original inner/outer wheel arch bowels




Going to use the existing profiles and outer wheel arch lip as much as I can – seen some real nasty’s trawling the net!!!





Looking ok so far a bit of filler work now should look good











Chopped out the bulk head for the servo unit - most people seem to go for the pedal box arrangement - but I'm grafting in a complete Scooby STi brake servo unit

Also going over the top on the cage – gone from the original rear hoop idea into a fully welded seamless cage – mainly to strengthen the tub enough to get rid of a hideous amount of chassis flex – so first mounting in – nice bit of 6mm plate

Most people are taking weight out of there cars to improve the bhp/ton ratio – I’m going about it the other way and putting additional weight over the back axle to keep the thing on the ground – typically most GT6/Spit engine transplants seem to be pumping out around 160 – 180 bhp so 300 bhp & 285 lbs/ft torque should still deliver the goods

Tuesday, June 24, 2008

New Clutch and Gearbox on

Finally found and won an OEM clutch on the bay for £50 - absolute bargin as they retail at £196 + vat from Volvo - Clutch is good for 300bhp in stock form


Flywheel bolts on via a ten bolt fixing - new high tensile bolts of course - far removed from the piece of rubber sh**e on the back of the Triumph crank




Gearbox in - just need to bolt it up - few minor adjustment on the rear rubber mount to sort out first

Sunday, June 08, 2008

Relocating the turbo

Been sorting out the relocation of the turbo unit - used some seemless 2' 1/2'' ID tube with a 5mm wall thickness so I could turn down and make a register to fit into the turbo housing







Then needed to step down from 2' 1/2'' to 2' and weld to the main exhaust rail




Not sure if I'm going to get it blasted and coated as its going to get kin hot




One size large outlet - going to buy in some performed stainless 3' tube and 'tig' up the exhaust - straight 3' all the way through into a transvers box of some sort








Sunday, June 01, 2008

Rad and Intercooler in place


Volvo rad in along with standard fan - didn't see any advantage in re inventing the wheel as my road car would sit in traffic all day long without over heating and puking its guts up - unlike the GT6







Same with the intercooler - one size large




Going to install a water spray jet - latent heat effect so will be the same as on a cold morning





Its a tight squeeze but it all fits - also big oil cooler in aswell


Tuesday, May 20, 2008

Random track photo's












Top left: Me at Goodwood Sprint 1988 - bottom left my mate Pete at Goodwood - top right me spinning at Lydden Hill









Above: Left gid line up Mallory 1990 - right my mate Pete's GT and bottom me at Snetterton 1991


















Above: Top left me at Snetterton 1994 - bottom left me at Brands Hatch - middle prep for Brands Hatch - right Hugh Davis at Goodwood Sprint 1988









Above: Left me at Snetterton 1994 - above right me at Brands Hatch 1991



2.3cc Fuel Injection - 1994 race engine - below on the trailer going home - You can just see the rear disc conversion!!










Being towed away after crash at Pembrey 1994 - only got three wheels???



Right in the pits at Snetterton 1994







TR 4 spinning at Snetterton 1994



Right 2500cc Spitfire






Eddie Wilkins 1300 Spit - won the Championship that year 1991


Practice line up - Mallory 1991




In the pits at Goodwood 1993




Nice arse!!!!





Pembrey race 1994 - still got 4 wheels!!!



No - I've only three wheels!!!




Quick 1500 left hooker




Right Rob's 2100 cc fuel injected GT - Mallory 1991 - trusty tow cars behind!!


Testday Goodwood late 1992