Wednesday, April 15, 2009
Lost the plot over the last 3 months and not really done anything with the car
Finally finished the 3' down pipe and the first section under the gearbox - less a bit of flap disc action too clean it up and get it blasted and coated
Started back on the rear end panelling and rear deck area - I really hate body work and have lost the will to live with it !!!
Starting to look at jigging up the roll cage - going to weld it in and mount to chassis
Not going to run a boot floor for easy access to tank etc - but will be looking at some under body areo mods so might even get a complete alloy flat plate to cover the entire underneath of the tub
Going for the single NASCAR type look wiper blade
Renault wiper motor tucks up nicely and gets rid of that piece of crap taking up space on the bulk head
Posted by
GT5-R
Monday, December 29, 2008
Tuesday, October 14, 2008
Only GT6 with a drivers airbag?

Will obviously disable the air bag for track use - but all that said a modern safety upgrade???
Using the Volvo steering column has serveral advantages - one being its completely adjustable - up and down & forwards and back ward - unlike the micky mouse Triumph arrangement. Also means I can plug the Volvo wiring loom straight in - so no messing around with 2 looms - indicators, lights, ignition barrell etc

Will obviously disable the air bag for track use - but all that said a modern safety upgrade???
Posted by
GT5-R
Sunday, September 21, 2008
Aero dynamics - well sort of !!


Been wanting to look under the roof lip strip since 1987 when I did some minor repairs - which have pretty much lasted the time and saved the roof lip
On the face if it the lip was pretty good - however two minor cuts with a hacksaw and the finishing strip was off to reveal rust!!!
Most of the lip although pretty rusty is all in one piece - until it got chopped off with the grinder

Not sure about you but I've never seen a GT6 that has been de-seamed that looks right - it looks like when you cut your eye brows off - not that I've done that either
Rather than de-seaming I'm removing the lip over the majority of the screen and seam welding the roof & leaving 3 short sections so I can put the finishing strip back on - this will allow the air to flow between the it rather than around it

You can just see the gap below - hope to reduce drag around the windscreen area
Roof back to bare metal
Posted by
GT5-R
Sunday, September 14, 2008
Body Work Continue's
Servo unit fits like a glove - however will need to run a remote reservoir as I would need to chop the windscreen frame out!!

I really hate body work!!!
Been working away on the brake conversion and the rear end mods
Bulkhead has been cut out the way completely along with the dash top and dash itself - going to graft a Volvo steering column in as its going to a much easier to sort all the electrics out - indicators lights and ignition
Cut the old braces out and reused so should stiffen it all up
Servo unit fits like a glove - however will need to run a remote reservoir as I would need to chop the windscreen frame out!!Back end is on going and stating to get on my t*ts
Had to revamp the location for the wipe motor due to the servo mods - going to run a single blade NASCAR style - so plugged the original holes and washers

Posted by
GT5-R
Monday, September 01, 2008
Breaking System Mods
Started work on the braking system - using a Subaru Impreza Turbo servo unit

Easier to cut the entrie rear bulk head panel out the way
Reshaped the top of the scuttle
Need to make a bracket then reinforce the bulkhead

Started to sus out the wiring loom - nightmare!!!!

Finished off the oil cooler as well

Started work on the braking system - using a Subaru Impreza Turbo servo unit
Easier to cut the entrie rear bulk head panel out the way
Started to sus out the wiring loom - nightmare!!!!
Finished off the oil cooler as well
Posted by
GT5-R
Thursday, June 26, 2008
Rear Wheel Arch Mods
Started the rear end mods to accommodate the wider wheel track and 16’ rims


Decided to roll a new inner wheel arch from a sheet of 18 guage to replace the original inner/outer wheel arch bowels

Going to use the existing profiles and outer wheel arch lip as much as I can – seen some real nasty’s trawling the net!!!

Looking ok so far a bit of filler work now should look good

Started the rear end mods to accommodate the wider wheel track and 16’ rims


Decided to roll a new inner wheel arch from a sheet of 18 guage to replace the original inner/outer wheel arch bowels

Going to use the existing profiles and outer wheel arch lip as much as I can – seen some real nasty’s trawling the net!!!

Looking ok so far a bit of filler work now should look good

Chopped out the bulk head for the servo unit - most people seem to go for the pedal box arrangement - but I'm grafting in a complete Scooby STi brake servo unit
Also going over the top on the cage – gone from the original rear hoop idea into a fully welded seamless cage – mainly to strengthen the tub enough to get rid of a hideous amount of chassis flex – so first mounting in – nice bit of 6mm plate
Most people are taking weight out of there cars to improve the bhp/ton ratio – I’m going about it the other way and putting additional weight over the back axle to keep the thing on the ground – typically most GT6/Spit engine transplants seem to be pumping out around 160 – 180 bhp so 300 bhp & 285 lbs/ft torque should still deliver the goods
Posted by
GT5-R
Tuesday, June 24, 2008
New Clutch and Gearbox on

Finally found and won an OEM clutch on the bay for £50 - absolute bargin as they retail at £196 + vat from Volvo - Clutch is good for 300bhp in stock form

Flywheel bolts on via a ten bolt fixing - new high tensile bolts of course - far removed from the piece of rubber sh**e on the back of the Triumph crank
Posted by
GT5-R
Sunday, June 08, 2008
Relocating the turbo
Been sorting out the relocation of the turbo unit - used some seemless 2' 1/2'' ID tube with a 5mm wall thickness so I could turn down and make a register to fit into the turbo housing
.jpg)
Then needed to step down from 2' 1/2'' to 2' and weld to the main exhaust rail

Not sure if I'm going to get it blasted and coated as its going to get kin hot
One size large outlet - going to buy in some performed stainless 3' tube and 'tig' up the exhaust - straight 3' all the way through into a transvers box of some sort

Been sorting out the relocation of the turbo unit - used some seemless 2' 1/2'' ID tube with a 5mm wall thickness so I could turn down and make a register to fit into the turbo housing .jpg)
Then needed to step down from 2' 1/2'' to 2' and weld to the main exhaust rail

Not sure if I'm going to get it blasted and coated as its going to get kin hot
One size large outlet - going to buy in some performed stainless 3' tube and 'tig' up the exhaust - straight 3' all the way through into a transvers box of some sort

Posted by
GT5-R
Sunday, June 01, 2008
Rad and Intercooler in place


Its a tight squeeze but it all fits - also big oil cooler in aswell
Volvo rad in along with standard fan - didn't see any advantage in re inventing the wheel as my road car would sit in traffic all day long without over heating and puking its guts up - unlike the GT6

Same with the intercooler - one size large

Going to install a water spray jet - latent heat effect so will be the same as on a cold morning
Its a tight squeeze but it all fits - also big oil cooler in aswell
Posted by
GT5-R
Subscribe to:
Posts (Atom)


























